The short answer: if your AquaTru isn’t filtering, it’s usually one of three things: a tank or the filter door isn’t seated (the unit won’t start), air is trapped after a filter change (it stops mid-cycle), or scale has clogged the pump and RO filter (it runs slowly or not at all). Seat both tanks and the side panel, lift and replace the clean water tank to clear trapped air, and descale if one tank takes more than 25 minutes. A new AquaTru filters a tank in 10 to 15 minutes.

To reset the change-filter light on a Classic or Carafe, press and hold the reset button for 5 seconds after installing the new filter.

Quick Fixes

ProblemLikely causeFix
No lights, won’t turn onPower switch, adapter, tank or filter door not seatedCheck the switch on the back, the adapter at both ends, both tanks and the filter-door magnet
Blue light on but it won’t pumpTanks not seated, filter cover not fully on, or water in the clean tank’s handleReseat tanks and cover; dry the handle
Sounds like it’s running, no water comes throughScale in the pump and RO filterDescale; replace the RO filter if it stays slow
Over 25 minutes per tankScale buildup or a worn RO filterDescale; replace the RO filter if it takes over 30 minutes
Stops mid-filtration after a filter changeTrapped air in the filter housingLift the clean water tank a few inches and set it back, up to 5 times
Carafe stops, red and blue lights blinkMaintenance mode: a cycle took 30 minutes or moreDescale the Carafe
A numbered filter light stays onThat filter is dueReplace it, then hold reset for 5 seconds
Leaks after changing filtersFilter not fully seated or lockedPush filters all the way in and lock them; match labels
Water drips from the clean tank handleTank filled up to the sensorDispense a little so the level stays below the sensor
Filtered water comes out warmClogged RO filterReplace the RO filter and descale
Bad tasteNew filters not flushed, or dirty tanksRun 4 tanks through; wash tanks weekly

Sources: AquaTru support center articles and the AquaTru Classic owner’s manual.

AquaTru Won’t Turn On or Isn’t Filtering

Go through AquaTru’s checklist in order:

  1. Power: the switch on the back is on, the adapter is pushed fully into both the base and a working outlet.
  2. Tanks: the tap water tank is full and the clean water tank is empty, and both are pressed fully onto the base.
  3. Side panel: the filter door is closed flush with the top of the control panel. A small silver magnet inside the bottom right corner of the door tells the unit it’s closed; if it’s missing or loose, the AquaTru won’t run.
  4. Blue light test: lift the tap water tank off the base. If the round blue light comes on, the unit has power, and the problem is a seating issue or water in the clean tank’s handle. If no light comes on, it’s the switch, adapter, outlet or the base itself. AquaTru notes that wastewater scale can damage the base.

(AquaTru: Why won’t AquaTru turn on after I changed my filters?)

Slow Filtering and Descaling

Hard water scales the pump and RO membrane, the most common reason an AquaTru slows down or runs with no water coming through. AquaTru’s rule: descale if a tank takes more than 25 minutes, and replace the RO filter if a tank takes over 30 minutes after descaling.

Classic descaling (AquaTru instructions):

  1. Remove the filter cover, wait 60 seconds, then remove the filters and install the AquaTru descaling filters.
  2. Warm 1 gallon of purified or low-TDS water to 100 to 120°F (not boiling) and fill the tap tank to half an inch below the handle.
  3. Stir in 2 packets of descaling powder for 30 seconds.
  4. Filter for 5 minutes, then let it soak for 15 minutes.
  5. Pour the clean tank’s water back into the tap tank and filter it again, then discard both tanks.
  6. Run 2 tanks of cold tap water, reinstall your filters (or a new RO filter), and wash both tanks.

The Carafe uses the same process with three-quarters of a gallon of water at 80 to 120°F and 1 packet of powder. After 5 minutes of filtering, turn the unit off and let it soak 15 minutes, no longer than 30.

AquaTru recommends monthly descaling in hard-water areas to extend RO filter life. Its descaling powder costs $9.95 and the Carafe descaling kit $19.95.

Prevent it: always pour out the water left in the tap tank before refilling. AquaTru says that leftover water can hold six times the contaminants of your tap water, and topping it up speeds scaling. AquaTru doesn’t recommend its countertop units for water harder than 10 grains per gallon (171 mg/L) unless it’s softened first or you descale regularly.

AquaTru Stops in the Middle of Filtering

After a filter change, this is usually trapped air. AquaTru’s fix: with the tap tank full and the clean tank not full, lift the clean water tank a few inches off the base and set it back down. Repeat up to 5 times.

If it isn’t right after a filter change, it’s scale (see descaling above) or the tap tank ran dry. The Classic’s manual adds: turn the unit off and on, empty and refill the tap tank, reseat the clean tank, and if it still stops, open the filter bay for a minute to let it decompress, then reseat each filter one at a time.

Carafe maintenance mode: if a Carafe cycle takes 30 minutes or longer, it stops and a red and blue light blink. That’s maintenance mode, and it means the Carafe needs descaling. A healthy Carafe fills its 64 oz carafe in about 15 minutes.

How to Reset the Filter Light on an AquaTru

During filtering, the lights cycle through the filter numbers. When a filter is due, its numbered light stays on:

  • Light 1 or 2: Pre/Carbon filter (every 6 months)
  • Light 3: RO filter (every 2 years)
  • Light 4: VOC carbon filter (every year)

Classic and Classic Smart: after replacing the filter, press and hold the filter reset button for 5 seconds. The light turns off and the lights resume cycling.

Carafe: same 5-second hold. If the light doesn’t turn off, let the unit filter for 5 seconds, remove the glass carafe, then hold reset for 5 seconds again (AquaTru).

Smart models: you can also reset filter life in the AquaTru app.

The unit tracks both time and gallons. If the light won’t go off after a reset and the filter is new, AquaTru’s manual blames trapped air in the system.

AquaTru Leaking

  • After a filter change: the filter probably isn’t fully seated. Push each filter all the way in, check that the label on the back matches the one above the manifold, and press the lock down until it clicks. On a new Carafe, remove the blue rubber caps first. Wetting the O-rings with clean water helps the Classic’s filters seat.
  • Some water when changing filters is normal. Wait 60 seconds after opening the cover before pulling a filter; drain holes in the base let spilled water out.
  • Down the clean tank’s handle: the tank filled to the sensor and water wicked into the handle. Dispense a little so the level stays below the sensor.
  • From the dispenser spout: a second or two of dripping after you release the button is normal. Longer than that means the clean water tank needs replacing; contact AquaTru.
  • A loose filter: compare the O-rings; if a filter fits loosely, it’s defective.

Other Problems

  • Bad taste: flush new filters by running 4 tank cycles, and wash both tanks with soap and water weekly.
  • Warm filtered water: a clogged RO filter makes the pump run hot. Replace the RO filter and descale.
  • High TDS: an RO filter typically lowers TDS about 90% from your tap reading. Below 80%, replace the RO filter.
  • Cloudy tap tank: micro air bubbles released by the RO membrane are normal.
  • Mold or algae: sanitize the tanks with a bleach solution for at least 30 minutes, rinse, and run a tank through before drinking. Keep the unit out of direct sunlight.
  • Vacation: turn it off, wash and dry the tanks, then run 4 tanks when you return. Replace filters that sat unused for 3 months or more.

Can You Use Generic Filters in an AquaTru?

You can buy them, but you lose what makes an AquaTru worth buying. AquaTru’s IAPMO certifications to NSF/ANSI 42, 53, 58 and 401 cover the system with its own filters, part numbers AT2001 to AT2004 for the Classic. A third-party cartridge isn’t covered by those listings, and AquaTru doesn’t publish compatibility with any of them.

AquaTru’s one-year warranty excludes filters and “damage caused by accident, misuse or any use other than as intended and described” in the manual. If a generic filter leaks or damages the pump, expect AquaTru to treat it that way. Also note the Carafe uses smaller filters than the Classic, Classic Smart and Under Sink models, so Classic filters don’t fit it.

Where to Buy AquaTru Replacement Filters

AquaTru sells filters on aquatru.com and by phone at 800-220-6570. Prices on November 15, 2026:

FilterClassicCarafeReplace every
Pre/Carbon filter$29.95$29.956 months (Classic 600 gal; Carafe 300 gal)
RO filter$59.95$59.952 years (Classic 1,200 gal; Carafe 600 gal)
VOC carbon filter$39.95$39.951 year (Classic 600 gal; Carafe 300 gal)
pH + Mineral Boost Alkaline VOC$49.95$49.951 year

AquaTru’s filter subscription for the Classic costs $79.88 in year one (2 Pre/Carbon, 1 VOC) and $127.84 in year two (adds the RO filter). Our countertop RO filter cost breakdown compares that with other brands, and our AquaTru Classic vs. Carafe comparison covers the two models’ filter lives.

Classic replacement filters

AquaTru Classic 1-Year Filter Pack

Two Pre/Carbon filters and one VOC carbon filter: a year of filters for the Classic, Classic Smart and Under Sink.

Carafe replacement filters

AquaTru Carafe One-Year Filter Combo Pack

AquaTru's own Pre/Carbon and VOC carbon filters for the Carafe. Carafe filters don't fit the Classic.

AquaTru Warranty

AquaTru purifiers carry a one-year limited warranty on materials and workmanship from the original purchase date, for the original buyer. Filters aren’t covered, and a shipping and processing fee applies to warranty service. A 3-year extended warranty costs $49.95. The Classic manual also warns that not discarding the leftover tap-tank water before refilling can damage the unit and void the warranty. Call 800-220-6570 for service.

AquaTru Troubleshooting FAQ

Why is my AquaTru not filtering water?

Check that both tanks and the filter door are fully seated, the tap tank is full and the clean tank is empty. If the pump runs but no water comes through, scale has clogged the pump and RO filter; descale it.

How do I reset the filter light on my AquaTru?

After replacing the filter, press and hold the reset button for 5 seconds. On a Carafe, if the light stays on, let it filter for 5 seconds, remove the glass carafe and hold reset again.

Why does my AquaTru stop in the middle of filtering?

After a filter change, air is trapped in the housing: lift the clean tank a few inches and set it back, up to 5 times. Otherwise it’s scale or an empty tap tank.

What do the blinking red and blue lights on an AquaTru Carafe mean?

Maintenance mode. A cycle took 30 minutes or more, and the Carafe needs descaling.

How long should an AquaTru take to filter?

10 to 15 minutes per tank when new. Descale at 25 minutes; replace the RO filter if it’s over 30 minutes after descaling.

Can you use generic filters in an AquaTru?

They exist, but AquaTru’s certifications cover only its own filters, and the warranty excludes damage from use not described in the manual. Carafe filters also differ from Classic filters.

Where can I buy AquaTru replacement filters?

From aquatru.com or AquaTru’s customer service line (800-220-6570). Pre/Carbon filters cost $29.95, RO filters $59.95 and VOC filters $39.95.

How often do AquaTru filters need replacing?

Classic: Pre/Carbon every 6 months or 600 gallons, VOC every year or 600 gallons, RO every 2 years or 1,200 gallons. The Carafe’s filters last the same time but half the gallons.