The short answer: vacuum the carpet, fill the Big Green’s clean water tank to the FILL line with hot tap water and two capfuls of Bissell formula, recline the handle and make one slow wet pass forward and one back while holding the trigger. Then release the trigger and make slow dry passes over the same strip until you can’t see water coming up. Empty the dirty tank like a bucket when it fills, refill, and keep going. Bissell says carpet typically dries in 30 to 45 minutes.

The steps below are from Bissell’s 86T3 user guide and its product page. The Big Green doesn’t heat water, weighs 42 pounds, and has a 1.75-gallon clean tank, a 25-foot cord and a 9-foot hose.

Before You Start

  1. Move furniture out if you’re cleaning the whole room (optional). For furniture you can’t move, Hoover’s carpet cleaner manual suggests aluminum foil or wax paper under the legs so wood finish doesn’t stain the wet carpet; the same trick works here.
  2. Vacuum thoroughly with a dry vacuum. Bissell lists this as a required step. See should you vacuum before using a carpet cleaner.
  3. Plan an exit. Start in the corner farthest from the door so you don’t walk across wet carpet.
  4. Pretreat traffic lanes and stains (optional). Spray Bissell Tough Stain Pre-Cleaner on entryways, hallways and stains and let it sit at least 3 minutes. Test it on a hidden spot first.
  5. Test Berber. Bissell warns that repeated strokes can fuzz some Berber carpets. Run the machine over a hidden area first.

Fill the Clean Water Tank

  1. Pull the dirty water tank handle upright and lift the dirty tank off.
  2. Lift the clean water tank off the base and unscrew its cap.
  3. Fill to the FILL line with clean, hot tap water. Don’t boil or microwave water.
  4. Measure Bissell formula with the cap: fill the cap to the line twice for each full tank.
  5. Screw the cap on and set the tank back on the base.
  6. Set the dirty tank back on top and push the handle back to lock it.

Use a genuine Bissell formula. The guide says non-Bissell solutions “may harm the machine and will void the warranty.” The box includes three 8-ounce bottles of PRO MAX Clean + Protect. See what solution to use in a Bissell carpet cleaner.

Clean the Carpet

  1. Plug into a grounded outlet and turn the power switch to ON (I).
  2. Recline the handle by pushing down on the green lever at the back while pulling the handle back. The brush only runs when the handle is reclined.
  3. Wet pass: hold the trigger and make one slow pass forward and one back.
  4. Dry pass: release the trigger and make one slow pass forward and back over the same strip.
  5. Repeat the wet and dry passes until the solution coming up looks clean.
  6. Finish with dry passes (no trigger) until you can’t see any more water being pulled up. This is what speeds drying.
  7. Overlap each strip slightly and work backward toward the exit.

Bissell’s cautions: don’t overwet, and don’t run over loose objects or rug edges. A stalled brush can wear the belt out early. If something jams the brush, the circuit breaker shuts it off: unplug, remove the object and plug back in to reset.

Empty the Dirty Water Tank

  1. Pull the dirty tank handle upright and lift the tank off.
  2. Carry it like a bucket to a utility sink, toilet or outside.
  3. Push the handle all the way forward, lift the top off and pour out the dirty water.
  4. Pick out hair and debris. Bissell notes that carpets that have never been deep cleaned often release a lot of it.
  5. Refill the clean tank with hot tap water and formula and continue.

If suction drops before the tank is full, the red float door may have closed after a bump or a fast stroke. Turn the machine off so it reopens, then turn it back on. See carpet cleaner not picking up water.

Stairs, Upholstery and Spots With the Hose

  1. Check the upholstery tag: “W” or “WS” means you can use the machine. Don’t use it on “S” (with a slash), “X”, “Dry Clean Only”, velvet or silk. Test for colorfastness.
  2. Vacuum the fabric or stairs.
  3. Fill the clean tank as above.
  4. Connect the solution hose to the connection point next to the flow indicator, turning clockwise until it locks. Open the hose latch on the front and lock the hose in.
  5. Attach the 6-inch Tough Stain Tool.
  6. Press the red trigger to spray, move the tool slowly back and forth, then release the trigger to suck up the dirty water. Work in small sections.
  7. Rinse the tool under running water and let it dry.

Keep the machine level and on the floor at the bottom of the stairs; Bissell warns to be extra careful on stairs. More in how to clean stairs with a carpet cleaner and can you use a carpet cleaner on a couch.

After Cleaning

  1. Turn the power off, unplug and wrap the cord.
  2. Empty both tanks and rinse them with hot tap water. The top half of the dirty tank can be rinsed through the nozzle area.
  3. Rinse the tools and run tap water through both ends of the hose.
  4. Let the tanks dry before storing. Don’t store the machine where it can freeze: Bissell says freezing damages internal parts and voids the warranty.
  5. Once the carpet is dry, vacuum again to pick up hair and fuzz the cleaning loosened.

Bissell says to deep clean every 6 to 12 months, more often with pets, kids or heavy traffic. See how often should you clean carpet.

$429 on Amazon, Nov. 21, 2026

Bissell Big Green Machine Professional (86T3)

1.75-gallon clean tank, 10.5-inch path, 25-foot cord, 9-foot hose with a 6-inch stain tool and a 5-year warranty.

Big Green How-To FAQ

How much solution do you put in a Bissell Big Green?

Fill the tank cap to its line twice for each full tank of water, per Bissell’s guide. That’s for Bissell’s 2X concentrated formulas.

Do you use hot or cold water in a Big Green?

Hot tap water. The Big Green doesn’t heat water, so the tap water is all the heat you get. Don’t boil or microwave it. See can you put hot water in a Bissell carpet cleaner.

How long does carpet take to dry after a Big Green?

Bissell says 30 to 45 minutes is typical, from its own tests on carpet with a protectant. Thick carpet, humid air and fewer dry passes take longer.

Why won’t my Big Green brush spin?

The brush only turns with the handle reclined. If it’s reclined and still not spinning, the belt may be off or broken, or the circuit breaker tripped. See Bissell carpet cleaner not spraying for the troubleshooting table.

Can you use the Big Green on area rugs?

Yes, if the rug’s tag allows water cleaning. Don’t run the brush over rug edges or fringe, which can stall it. See can you use a carpet cleaner on a wool rug.

Sources