The short answer: a Bissell carpet cleaner that won’t spray almost always has an empty or loosely seated clean water tank, a pump that has lost its prime, or a clogged filter or spray tip. Refill the tank with warm tap water and push it down until it seats, then turn the machine off and back on, wait a minute and pull the trigger again. If it still won’t spray, clean the debris filter under the tank and the spray tips. On ProHeat 2X uprights, a broken pump belt also stops the spray, because the same belt drives the pump and the brushes.

Unplug the machine before you check anything past the tank. Bissell’s guides all say to turn the power off and disconnect the plug “before performing maintenance or troubleshooting.”

Quick Fixes in Order

  1. Refill the clean water tank. Every Bissell troubleshooting table starts here. The TurboClean guide adds that water “might not come out of the nozzle if water level is too low,” so fill it to the WATER line, not halfway.
  2. Reseat the tank. Turn the power off, lift the tank out and set it back until it sits flat or clicks. A tank that’s a few millimeters high won’t open its valve.
  3. Re-prime the pump. On the Big Green, turn the power off, back on, wait one minute and then press the trigger. On portables, see the Little Green steps below.
  4. Clean the filter under the tank. The Big Green has a debris filter on the base; the ProHeat 2X Revolution and TurboClean have a red filter below the dirty water tank. Wipe off lint and hair by hand.
  5. Clear the spray tips. Bissell support suggests a soft brush or an old toothbrush, and a straightened paperclip for a tip on the end of the hose.
  6. Test the tank valve. Fill the tank, hold it over a sink and push up on the X-shaped valve in the cap. Water should flow out. If it doesn’t, soak the cap in warm water for 30 minutes; if it still won’t flow, the tank needs replacing.
  7. Check the belt (ProHeat 2X and other pump-belt uprights). If the brushes don’t turn either, the belt is off or broken. Bissell support notes that the brush roll and the pump share one belt on these machines.
  8. Check the gaskets. On tank-in-tank ProHeat models, the red or black rubber gasket on the tank feeder must be present and seated. A lost gasket has to be replaced.

Symptom, Cause and Fix

SymptomLikely causeFix (from Bissell’s guides)
No spray at all, tank fullTank not seatedPower off, lift the tank and reseat it
No spray right after fillingPump lost primeBig Green: power off, on, wait 1 minute, then trigger. Little Green: lift or gently squeeze the clean tank while holding the trigger
Spray weak, then stopsWater level too lowFill to the WATER line
Weak spray from the floor nozzleDebris filter cloggedUnplug, remove tanks, clear the filter on the base by hand
Hose and tool won’t spray, floor spray worksTool tip clogged, or hose not primedRemove the tool and test the bare hose; clear the tip with a paperclip. ProHeat 2X Revolution: hold the hose end below the water level in the tank to prime it
No spray and brushes don’t spinBroken or slipped beltReplace the belt (Bissell guides show the steps; belts aren’t covered by warranty)
No spray, valve on the tank cap won’t releaseStuck X-valveSoak the cap in warm water 30 minutes; replace the tank if it still won’t flow
Water leaks out the bottom when you pull the trigger unplugged (TurboClean)Normal gravity feedBissell calls this expected behavior; don’t squeeze the trigger when the machine isn’t running

Big Green (86T3)

Bissell’s 86T3 guide lists four causes for “reduced spray or no spray”:

  1. Water tank may be empty: fill the clean tank with hot tap water (not boiling).
  2. Tank may not be seated completely: turn the power off, remove the tank and reseat it.
  3. Pump may have lost prime: turn the power off (0) and back on (I), wait one minute, then press the trigger.
  4. Debris filter on the base is clogged: turn the power off and remove the debris by hand.

If the DirtLifter PowerBrush also isn’t turning, check that the handle is reclined (the brushes only run reclined), then check the belt and the circuit breaker. The breaker trips if something catches in the brush roll; unplug, remove the object and plug back in to reset it. Bissell warns that stalling the brush on rug edges can cause early belt failure. See how to use a Bissell Big Green for the full routine.

ProHeat 2X Revolution (1548, 3588F and Similar)

The ProHeat 2X Revolution guide gives two different no-spray cases:

  • Reduced spray or no spray from the floor nozzle: the clean tank may be empty or not seated, or the pump lost prime in hose cleaning mode. To re-prime, hold the end of the hose below the water level in the tank.
  • No spray through the hose and tool: the hose isn’t primed. With the machine off and unplugged, remove the nozzle from the foot, push a ballpoint pen into the black cylinder next to the screw until water bubbles up, remove the pen and reassemble the nozzle and hose.

Bissell support adds for ProHeat 2X uprights: both the formula tank and the 2-in-1 tank must have liquid in them before the machine sprays, the red rubber gaskets must be in place, and a broken belt stops the pump. Rinse the white solution filter under cool water on models that have one.

Also check that you’re pressing the power button, not the cleaning-mode switch. Bissell’s guide lists “Cleaning Mode switch mistaken for Power Button” under no power.

TurboClean (3952, 3948)

The TurboClean guide’s no-spray causes are an empty tank, a tank not seated completely, and a water level that’s too low. Refill to the WATER line and push the tank down until it’s seated. There’s no pump-prime step in this guide because the machine is gravity fed.

Little Green (1400B, 3369) and Little Green HydroSteam (3618)

Bissell’s current Little Green guide lists these no-spray causes:

  1. Spray nozzle clogged: clean the spray nozzle (remove the tool lens and rinse it under warm water).
  2. Clean water tank empty: refill.
  3. Insert at the bottom of the tank clogged: clean it.
  4. Pump needs priming: reseat the tank and hold the spray trigger. The older guide says to gently lift or squeeze the clean tank while holding the trigger.
  5. Tank valve stuck: free the valve on the tank cap with a small tool.

On the Little Green HydroSteam, prime the machine by holding the trigger over a sink or bowl until steam appears, and wait 30 seconds for the steam light before using a steam mode. Bissell says some water sprays instead of steam at first; keep holding the trigger for 5 to 10 seconds.

When It’s Time for Service

If the tank, filter, tips and belt all check out and it still won’t spray, the pump or trigger linkage needs a technician. Bissell says to call Consumer Care (1-800-237-7691) or an authorized service center, and not to return the machine to the store. Check your term on the Bissell carpet cleaner warranty page first: the Big Green and ProHeat 2X Revolution carry 5 years, the TurboClean and Little Green 1 year.

Using a non-Bissell formula can also cause problems: the Big Green guide says non-Bissell solutions “may harm the machine and will void the warranty.” See what solution to use in a Bissell carpet cleaner.

Bissell Not Spraying FAQ

How do you prime a Bissell carpet cleaner?

On the Big Green, turn the power off and back on, wait one minute, then press the trigger. On a ProHeat 2X Revolution, hold the end of the hose below the water line in the tank, or push a ballpoint pen into the black cylinder by the nozzle screw until water bubbles up. On a Little Green, reseat the tank and hold the trigger, or gently squeeze the tank while holding it.

Why is my Bissell spraying from the hose but not the floor?

The floor nozzle has its own path. Check that the tank is fully seated, clean the debris or red filter under the tank, and clear the spray tips on the foot. On ProHeat 2X uprights, also check the belt, since it drives the pump.

Why does my Bissell spray only a little water?

Low tank level, a partly clogged filter or spray tip, or a tank that isn’t fully seated. Fill to the WATER line, reseat the tank and clean the filter and tips.

Does a broken belt stop a Bissell from spraying?

On ProHeat 2X uprights, yes. Bissell support says the pump and brush roll run off the same belt. If the brushes have stopped turning too, replace the belt.

Can hard water stop a Bissell from spraying?

Mineral buildup can clog spray tips over time. For the Little Green HydroSteam, Bissell recommends distilled water when you use it without formula, to prevent hard water buildup.

Sources