The short answer: a carpet cleaner that stops picking up water usually has a full dirty tank (the float has shut off suction), a dirty tank or lid that isn’t sealed, or a clog in the nozzle, filter or hose. Empty the dirty water tank and press it back until it locks. Check that the lid, the rubber pour tab and the accessory hose door are closed. Then pull the nozzle cover and rinse out hair and lint. A higher-pitched motor sound with a sudden loss of suction is the float closing, which every Bissell and Hoover upright uses to keep water out of the motor.

Unplug the machine before you take the nozzle off. Bissell and Hoover both say to unplug before servicing.

Symptom, Cause and Fix

SymptomCauseFix
Motor sound rises, suction drops suddenlyDirty tank full; float closedTurn off, empty the dirty tank, reinstall
Float closed but tank isn’t fullFloat tripped by bumping, fast strokes or lifting the machine while onTurn off so the float drops, turn back on, slow your strokes
Weak suction from the startDirty tank or lid not seatedRemove and reseat the tank; latch the lid. On SmartWash, a visible yellow label means the lid isn’t on
Weak suction on ProHeat 2X / TurboCleanRubber pour tab on dirty tank not sealedPress firmly around every edge of the tab
Weak suction, hose attached or notAccessory hose door openClose and lock the hose door/port
Suction normal, water left in carpetNozzle clogged with hair or lintRemove nozzle; rinse; clear with Bissell’s clean-out tool
Suction weak on HooverDebris filter under the tank lid cloggedWipe it clean and let it dry
Tool on the hose won’t pick upClog in the tool or hoseRemove the tool and clear it; flush the hose with clean water
Dirty tank fills with foam, then shuts offWrong or too much formulaUse the maker’s formula at the measured amount
Little Green won’t pick upTool not flat on the surface, or latch openPress the tool flat and pull toward you; close the tank release latch

Full Dirty Tank and the Float

Every upright has a float stack in the dirty tank. When the tank fills, the float rises and shuts off airflow through the nozzle. Hoover’s SmartWash manual says to empty the tank “when the motor sound becomes higher pitched and there is a loss in suction.” Bissell’s TurboClean guide gives the same signs: a change in motor noise and less water coming up from the floor.

The float can also close when the tank isn’t full. Bissell’s Big Green guide lists a red float door that closes from “bumping an object or moving machine back and forth too quickly”: turn the machine off so the door drops open, turn it back on, and slow down. Hoover’s service instructions add that lifting the machine off the floor while it’s running can trip the float.

Clean the float when you empty the tank. On the ProHeat 2X Revolution and TurboClean, unscrew the ring at the bottom of the dirty tank, rinse the float stack, and reinstall it with the arrows lined up. Bissell warns that a ring that isn’t fully tightened leaks.

Air Leaks: Tanks, Lids, Tabs and Doors

Suction needs a sealed path from the nozzle to the motor. Any gap kills it:

  • Dirty tank seating. Lift the tank and set it back so it fits snugly. On the TurboClean, latch both side latches.
  • Tank lid. Hoover’s SmartWash dirty tank shows a yellow warning label when the lid isn’t secured.
  • Rubber quick-empty tab. ProHeat 2X Revolution, 3588F and TurboClean tanks have a pour tab on top. Bissell’s troubleshooting table lists a tab that isn’t sealed as a cause of lost suction: press firmly on all edges.
  • Accessory hose door. On ProHeat 2X uprights and the Hoover SmartWash, the hose port door has to be closed for floor suction. Hoover: “Unit may lose suction if not closed properly.”
  • Nozzle. A nozzle that isn’t clipped all the way in leaks air. Hoover: “The nozzle must be in the proper position for the unit to have proper suction.” Bissell’s TurboClean guide says to remove and reinstall the nozzle if you get no suction.

Clogs

  1. Nozzle. Pull the nozzle cover (Bissell ProHeat: press the two release buttons and lift; Hoover: lift the release and pull forward, not straight up). Rinse it, and on Bissell models use the nozzle clean-out tool in the thin slot where the nozzle touches the floor.
  2. Filters. Bissell’s ProHeat and TurboClean have a red filter below the dirty tank; Hoover has a debris filter under the dirty tank lid. Wipe them clean.
  3. Hose. Hoover’s SmartWash manual suggests dropping a coin through the hose and clearing it with a broom handle. Then flush with clean water.
  4. Brush roll. Hair wrapped around the brushes drags water around instead of letting the nozzle lift it. Comb it out.

Hoover Reset

Hoover’s service instructions list a reset for SmartWash and PowerDash units that won’t pick up after the checks above: unplug it, remove the nozzle cover and the brushes, put the nozzle cover back, plug it in and cycle the power on and off 4 times, then put the brushes back.

Little Green and Other Portables

Bissell’s Little Green guide lists: tank release latch not closed, poor tool position (press the tool flat so the nozzle touches the surface), a full dirty tank, a damaged tool, excess solution in the flex hose (lift the tool and point it up so water drains into the tank), and the wrong formula. Use Bissell portable formulas only. Hoover’s CleanSlate manual adds a clogged air path: remove the hose and flush it with clean water, and rinse the recovery tank debris filter.

If It Still Leaves the Carpet Wet

A machine that picks up normally still leaves water if you rush. Make extra dry passes with the trigger released until little water shows in the nozzle; Bissell’s Revolution guide suggests about 8 inches per second in Deep Clean. See how many passes with a carpet cleaner and how long carpet takes to dry.

Not Picking Up Water FAQ

Why does my carpet cleaner suddenly lose suction?

Usually the float closed because the dirty tank is full, or because you bumped something or moved fast. Turn it off, empty the tank, and turn it back on.

Why is my Bissell spraying but not sucking up?

Check the dirty tank seating, the rubber pour tab, the accessory hose door and the nozzle. On a Big Green, turn the machine off so the red float door can reopen.

Why is my Hoover not picking up water?

Hoover lists a full dirty tank, a loose lid or nozzle, a dirty debris filter, a clogged hose tool, and a unit that needs the four-cycle reset.

Why is my carpet cleaner tank filling with foam?

Too much formula or a formula not made for the machine. Bissell’s HydroSteam guide says to use only Bissell portable formulas at the right concentration to prevent excess foaming. Extra foam can trip the float early.

Can a clogged brush roll reduce suction?

It leaves more water behind. Comb out hair from the brushes and clean the nozzle.

Sources