The short answer: after every use, empty and rinse both tanks, take out and rinse the float stack in the dirty tank, wipe the red filter under the tank, rinse the nozzle and brushes, flush the hose with clean water, and let it all air-dry before you put it away. On ProHeat 2X Revolution and Revolution Pet Pro models, Bissell also has you run warm tap water through the machine for 15 seconds to rinse formula out of the lines. Never store it wet or where it can freeze.
Turn the machine off and unplug it first. Every Bissell guide says to disconnect the plug before maintenance.
After Every Use (All Bissell Uprights)
- Empty the dirty water tank into a sink, toilet or outside. Pick hair and debris out of the tank rather than pouring it down a drain.
- Rinse the dirty tank with warm or hot tap water. Bissell’s tanks aren’t dishwasher safe.
- Rinse the float stack. It’s the part that stops the tank overflowing, and dirt on it causes leaks and lost suction (steps by model below).
- Empty the clean water tank and rinse out leftover formula.
- Flush the lines with warm water (ProHeat 2X Revolution, Revolution Pet Pro).
- Clean the red filter under the dirty tank by wiping off lint and debris.
- Remove and rinse the nozzle, and clear it with the clean-out tool if hair is stuck in it.
- Comb the brush rolls to remove hair.
- Clean the hose and tools: rinse the tools and run clean water through the hose.
- Air-dry everything before you reassemble and store. Store indoors, dry, and above freezing.
ProHeat 2X Revolution and Revolution Pet Pro (1548, 3588F)
From Bissell’s Revolution guides:
Rinse the machine: empty the clean water tank, fill it with warm tap water and twist the cap on tight. Turn the machine on and hold the trigger for 15 seconds while making back-and-forth passes on a section of carpet, then release the trigger and extract the water. Empty the dirty tank again and empty the clean tank.
Dirty tank and float stack:
- Press the tank handle, tilt the tank toward you and lift it off with both hands.
- For a quick empty, pull the rubber tab on top and pour. Make sure the tab is sealed tight when you close it.
- For a full clean, unscrew the ring at the bottom of the tank and pull out the float stack. Rinse it.
- Put the float stack back by lining up the arrows so they point at each other (it only fits that way), then twist the ring until it locks. Bissell warns water may leak if the ring isn’t fully tightened.
- Wipe the red filter below the tank.
Nozzle and brushes: press the two release buttons and lift the cover off (on the older 1548, flip the hose door open and lift the nozzle). Rinse the nozzle, push the clean-out tool through the thin slot that touches the floor, and comb hair out of the brush rolls. Push the cover back down until both sides click.
Hose and tools: after hose cleaning, Bissell says to turn the machine on and suck up warm clean water to rinse the inside of the hose and tool. Detach them, close the accessory hose door and let them air-dry.
Big Green (86T3)
- Turn the power off (0), unplug and wrap the cord.
- Empty both tanks and rinse them with running hot tap water.
- Rinse the top half of the dirty tank through the nozzle area.
- Take the tools off the hose, rinse them under running water and let them dry. Remove the hose from the machine and run tap water through both ends.
- Before turning off after hose work, suck up some clean water to rinse the inside of the hose, then point the tool up so the remaining water drains into the dirty tank.
- Make sure both tanks are empty, rinsed and dry before the next use, and store the machine where it can’t freeze.
Bissell’s guide is clear that freezing “will damage internal components and void the warranty.”
TurboClean (3952, 3948)
- Turn off, unplug, and release the dirty tank by pulling the side latches up and out.
- Grab the top of the nozzle and pull it up and away from the machine. Wipe it clean, and wipe the red filter under where the dirty tank sits.
- Unscrew the ring at the bottom of the dirty tank and rinse the float. Bissell says keeping the float clean keeps the tank from overflowing and the seal intact.
- Reassemble the float by lining the arrow up with the notch on the tank, then twist the ring to lock it.
- Reinstall the nozzle by lining up the ribs at each end, lowering it into place and pressing the top down so it fits snugly.
- Once the tank is dry, latch it back on.
Why the Machine Smells (and How to Stop It)
A sour or musty smell is almost always dirty water or damp debris left in the dirty tank, float, nozzle or hose between uses. Empty and rinse those parts the same day, and let the tanks dry with the caps off before you store them. If a smell is already there, take the float stack and nozzle apart, rinse them, and flush the hose with warm water. Bissell’s manuals don’t approve bleach or household disinfectants in the machine; they say to use only Bissell formulas. For portables, see how to clean a Bissell Little Green.
Things Bissell Says Not to Do
- Don’t use boiling water or microwave the tank. Warm tap water tops out at 140°F on the ProHeat 2X and TurboClean.
- Don’t put the tanks in the dishwasher (Bissell’s Little Green guide says plastic tanks aren’t dishwasher safe).
- Don’t use non-Bissell formulas or household cleaners: “Other formulas or household cleaners may cause defects or damage to the machine.”
- Don’t store it where it can freeze.
Cleaning a Bissell Carpet Cleaner FAQ
Do you need to clean a Bissell after every use?
Yes. Every Bissell guide says to empty and rinse the tanks after cleaning and dry them before the next use. The float stack, filter and nozzle collect hair and grime that cause smells, leaks and weak suction.
How do you clean the float on a Bissell carpet cleaner?
On ProHeat 2X Revolution and TurboClean models, unscrew the ring at the bottom of the dirty tank, pull the float out, rinse it, and reinstall it with the arrows lined up. Tighten the ring fully so it doesn’t leak.
Can I run vinegar through my Bissell to clean it?
Bissell’s blog says vinegar in a carpet or floor cleaner “can cause permanent damage.” Flush it with warm tap water instead. See can you put vinegar in a carpet cleaner.
How do I clean the hose on a Bissell carpet cleaner?
With the machine running, suck up a bowl of warm clean water through the hose and tool, then point the tool up to drain it into the dirty tank. On the Big Green, you can also detach the hose and run tap water through both ends.
Where is the filter on a Bissell carpet cleaner?
On the ProHeat 2X Revolution, Revolution Pet Pro and TurboClean, it’s the red filter on the base below the dirty water tank. The Big Green has a debris filter on the base.
Sources
- Bissell Revolution Pet Pro 3588, 3588F, 3589 user guide (PDF)
- Bissell ProHeat 2X Revolution 1548, 1550, 1551 user guide (PDF)
- Bissell Big Green 86T3 user guide (PDF)
- Bissell PowerForce/TurboClean 3938, 3939, 3952 user guide (PDF)
- Bissell Little Green 3369, 1400B user guide (PDF)
- Bissell blog: 4 DIY floor cleaning mistakes





