The short answer: a Hoover carpet cleaner stops spraying when the clean water tank or the solution tank is empty or not locked in, when a SmartWash is in Dry Only mode or isn’t moving forward, or when air is trapped in the pump. Fill both tanks and press them firmly into place. On a SmartWash, turn Dry Only off and push the machine forward, because it only dispenses on the forward stroke. If the hose won’t spray, lower it to the floor and hold the trigger for up to one minute to prime the pump. If that fails, flush the unit with warm water and do Hoover’s four-cycle power reset.
Unplug the cleaner before you remove the nozzle or brushes. Hoover’s manuals say to unplug before servicing.
Symptom, Cause and Fix
| Symptom | Cause | Fix (Hoover manuals and service instructions) |
|---|---|---|
| Nothing comes out on the floor | Clean water tank or solution tank empty | Fill both. SmartWash and PowerDash need liquid in both tanks |
| Nothing comes out on the floor | Tank not firmly in place | Press each tank FIRMLY until it locks |
| SmartWash won’t dispense | Dry Only mode is on | Turn Dry Only off; the unit won’t dispense in that mode |
| SmartWash dispenses only sometimes | It only dispenses moving forward | Push forward slowly; the wash light shows when it’s dispensing |
| PowerDash won’t dispense | Handle not fully installed | Reseat the handle until it clicks; Hoover says it won’t dispense otherwise |
| Still nothing after filling | System needs flushing | Warm tap water in both tanks, seat them, turn on, recline, push forward 3 to 4 times until water comes out |
| Still nothing after flushing | Unit needs a reset | Unplug, remove nozzle cover and brushes, refit the nozzle cover, plug in, cycle power on and off 4 times, refit brushes |
| Hose tool won’t spray after filling | Air trapped in hose and pump | Turn the cleaner on, lower the hose to the floor, hold the trigger up to 1 minute |
| Hose stops spraying mid-job | Tank empty, or loose connection at the solution port | Refill; check the hose connection on the foot |
| Hose won’t spray after priming | Clog, or failed pump | Clear both hose ends and push a small object into the hose solution port; if it still fails, call 1-800-944-9200 |
SmartWash and SmartWash+ (FH52000 Series, FH53000 Pet)
The SmartWash meters water and solution automatically, which adds two causes a manual machine doesn’t have:
- Dry Only mode. Pressing Dry Only stops all dispensing so the machine only extracts. Hoover’s service sheet says the unit “will not dispense if in the DRY ONLY mode.”
- Forward motion. Solution comes out only as you push forward; pulling back dries. If the wash light doesn’t come on when you push forward, Hoover says the problem may be the internal board.
Then work through the general steps:
- Fill the clean water tank with warm water to the top and the solution tank with Hoover solution, and press both firmly into place.
- Flush: add warm tap water to both tanks, seat them, clean any debris off the distributor bar, turn the unit on, recline the handle and push forward continuously 3 to 4 times until water comes out the bottom again.
- Reset: unplug it, pull the nozzle cover and take out the brushes, replace the nozzle cover, plug it in and cycle the power on and off 4 times. Put the brushes back and test.
- Hose: check both ends for clogs, push a small object into the hose solution port, then prime by lowering the hose to the floor and holding the trigger for up to one minute.
PowerDash Pet and PowerDash Pet Advanced (FH50700, FH55000 Series)
Hoover’s PowerDash service instructions list:
- Tanks: the clean water tank and solution tank must be filled and fitted properly.
- Handle: “The unit will not dispense if the handle is not properly installed.” Pull the handle out and push it back in until it seats.
- Flush: warm tap water in both tanks, seat them, turn on, recline and push forward 3 to 4 times until water comes out.
- Reset: the same nozzle-cover, brushes-out, four-power-cycle reset as the SmartWash.
- Hose (PowerDash Pet Advanced/Complete only): clear the hose ends, clean the tools, and prime by holding the trigger with the hose lowered to the floor for up to a minute.
CleanSlate Spot Cleaners (FH14000, FH14050, FH15000)
Hoover’s CleanSlate manual gives three causes for “cleaner won’t dispense”: the solution tank is empty, the solution tank isn’t installed properly, or the machine needs service. For “hose nozzle will not spray after filling,” the cause is air trapped in the pump and hose: turn the cleaner on, lower the hose to the floor and hold the trigger for up to one minute.
After each job, Hoover has you attach the Hose Rinse Tool, turn the unit on and hold the trigger for 30 seconds to flush the hose. A hose left dirty between jobs is a common source of clogs; see how to clean a carpet cleaner for the same idea on Bissell machines.
Solution Problems
Hoover’s manuals warn: “use only Hoover cleaning products intended for use with the appliance.” Another brand’s formula, or a household cleaner, can foam or leave residue in the lines. Hoover’s SmartWash manual also recommends a final pass with water only to rinse solution out of the carpet. See can you use Bissell solution in a Hoover and can you use a carpet cleaner with just water.
When to Call Hoover
If the pump still won’t deliver after priming, Hoover’s troubleshooting table says the pump may be defective: call 1-800-944-9200 (Mon–Fri) and have the model number from the data plate on the back of the machine. Don’t return it to the store. The SmartWash manual includes a limited five-year warranty for domestic use; check your model’s term on the Hoover carpet cleaner warranty page.
Hoover Not Spraying FAQ
How do I reset my Hoover SmartWash?
Unplug it, remove the nozzle cover and take out the brushes, put the nozzle cover back, plug it in, and turn the power on and off 4 times. Then reinstall the brushes and test. Hoover gives the same reset for the PowerDash.
Why does my Hoover SmartWash only spray sometimes?
It dispenses only while you push forward, and not at all in Dry Only mode. Pulling back is the drying stroke.
How do you prime a Hoover carpet cleaner hose?
Turn the cleaner on, lower the hose to the floor and hold the trigger for up to one minute. That pushes trapped air out of the pump and hose.
Why is my Hoover leaking but not spraying?
A tank that isn’t pressed fully into place can drip without feeding the pump. Reseat each tank firmly. Hoover also notes some residual water drips from the brushes after use, which is normal.
Do both Hoover tanks need liquid to spray?
On the SmartWash and PowerDash, yes. Hoover’s service instructions say to make sure the clean water tank and the solution tank are both full and locked in.





