A bidet seat fits most two-piece toilets and many one-piece toilets. Take three measurements: bolt holes to the front of the bowl (about 16.5 inches is round, 18.5 inches is elongated), the distance between the bolt holes (5-1/2 inches is standard), and the gap from the bolt holes to the tank (most seats need 1-1/2 to 2 inches). Toilets with a deep French curve, where the tank’s sides sweep forward around the seat, are the usual misfit; a bidet attachment or a slim seat often fits where a full seat won’t. Electric seats also need a grounded GFCI outlet within reach of their cord (TOTO says within 3 feet of the toilet).
The Three Measurements
- Bowl length: round or elongated. Measure from the center of the seat bolt holes to the front edge of the bowl. TOTO, Alpha and Bio Bidet give about 16.5 inches for round and 18.5 inches for elongated. Brondell’s ranges are 16 to 17-3/4 inches (round) and 18 to 19-1/2 inches (elongated). Buy the seat that matches; Bio Bidet warns that a seat on the wrong bowl can break “from added stress.”
- Bolt-hole spacing. Measure center to center between the two seat bolts. 5-1/2 inches is standard in the US.
- Clearance to the tank. Measure from the center of the bolt holes back to the tank (or the wall of a one-piece toilet). This is the measurement that rules out most toilets.
Also measure the tank front to the bowl front if the seat might overhang: Brondell suggests the round Swash (19.4 inches long) on an elongated toilet if that distance is under 20-1/2 inches.
What Each Maker Requires
| Maker / models | Bolt spacing | Bolt holes to tank | Bowl length | Notes |
|---|---|---|---|---|
| TOTO Washlet | About 5-1/2 in | 2 in (elongated); 2-1/2 in for round C2/C5 | 18.5 in E / 16.5 in R | Needs 8 in of flat space from the toilet’s center to the edge of the bowl’s flat surface; GFCI outlet within 3 ft; French-curve toilets may not fit |
| Brondell Swash (most) | 5-1/4 to 8 in | 1-1/2 in | 18 to 19-1/2 in E / 16 to 17-3/4 in R | Under 2 in, the seat may overhang the front of the bowl; T-valve needs a 7/8 in fill-valve connection |
| Brondell SE400, SE600, IS707, CL510, CL950 | Exactly 5-1/2 in | 1-1/2 in | Same | |
| Brondell Thinline T22/T44/T66, CL2200, LS1600/1800 | 5-1/4 to 8 in | 2 in | Same | |
| Brondell attachments | 5-1/4 to 8 in | 3/4 in | Any | Fit most one-piece and French-curve toilets (Brondell gives a separate French-curve check) |
| Alpha JX2 | 5-1/2 in | 1-1/2 in | 18.5 in E / about 16.5 in R | |
| Alpha iX Pure, UX Pearl | 5 to 7 in | 1-1/2 in | Same | Alpha’s pick for compact elongated bowls |
| Alpha GX Wave | 5 to 7 in | 1-3/4 in | Same | |
| Bio Bidet seats and attachments | 5-1/2 to 7-1/2 in | 1-1/2 in | 18.5 in E / 16.5 in R | Deep French-curve toilets don’t fit well |
One-Piece Toilets
A one-piece toilet has the tank and bowl molded as a single unit. Whether a bidet seat fits depends on the shape where the tank meets the bowl:
- Tank meets the bowl at close to a right angle: usually compatible. Alpha lists the Kohler Memoirs, TOTO Ultramax and Supreme, and Woodbridge T-0001 as examples.
- French curve (tank sides curve forward around the seat): may not fit. Alpha says only its JX fits the Kohler San Raphael, and none of its seats fits the Kohler Rialto. Bio Bidet asks owners of deep French-curve toilets to contact it with the model number.
- Not sure? Measure the bolt-to-tank gap at the narrowest point and check it against the table. An attachment needs much less room: 3/4 inch for Brondell’s.
Skirted, Compact and Wall-Hung Toilets
Skirted toilets (concealed trapway) usually take a bidet seat but may need extra parts. Alpha says they’re “usually compatible” but may require extra installation parts; Brondell’s example, the TOTO Legato, needs its alternative T-valve and top-mount hardware.
Compact elongated toilets have a shorter bowl than a full-size elongated. Alpha recommends its UX Pearl or iX Pure for them, though the JX2 also works.
Wall-hung toilets with an in-wall tank need an accessible 1/2 inch water supply for the bidet, which a plumber has to provide, per Brondell.
Don’t Forget Water and Power
- Water: bidets tee off the toilet’s fill valve. Brondell’s T-valves need a standard 7/8 inch fill-valve connection; if you can’t reach the fill valve, a handheld sprayer won’t fit either.
- Power (electric seats): a grounded GFCI outlet within reach of the seat’s cord, which runs about 3 to 5 feet depending on the model. TOTO voids its warranty without a 120 V GFCI outlet and the factory cord, and Kohler requires a dedicated GFCI circuit.
Slim seat for compact bowls
Alpha Bidet iX Pure
Low-profile seat that fits bolt spacing of 5 to 7 inches with 1.5 inches of tank clearance. Elongated; round sold too.
When a seat won't fit
LUXE Bidet NEO 185
An under-seat attachment with front and rear nozzles that keeps your current seat. No outlet needed.
Once you know your toilet fits, see the best bidet toilet seats, best bidet attachments or bidet attachment vs. bidet seat.
Will a Bidet Fit My Toilet FAQ
How do I know if my toilet is round or elongated?
Measure from the center of the seat bolt holes to the front edge of the bowl. About 16.5 inches is round; about 18.5 inches is elongated.
Do bidets work on one-piece toilets?
Many do. One-piece toilets where the tank meets the bowl at close to a right angle are usually compatible. Deep French-curve toilets, where the tank’s sides curve forward, often aren’t; an attachment or a slim seat is the fallback.
Can a bidet be installed on a skirted toilet?
Usually, but it may need extra parts. Alpha says skirted toilets are usually compatible with its seats, and Brondell’s example skirted toilet, the TOTO Legato, needs an alternative T-valve and top-mount hardware.
What if the bolt holes are too close to the tank?
Most seats need 1-1/2 to 2 inches. With less, look at a bidet attachment (Brondell’s need 3/4 inch) or a slim seat; Alpha’s GX Wave needs 1-3/4 inches and its iX Pure 1-1/2.
Does a WASHLET fit a non-TOTO toilet?
TOTO says Washlets fit most standard North American toilets, as long as there are about 2 inches from the tank to the bolt-hole centers on an elongated bowl and about 5-1/2 inches between the bolts. French-curve toilets may prevent installation.
Can I put an elongated bidet seat on a round toilet?
No. Bio Bidet advises against it, since the bowl supports the seat and a mismatched seat can break. Buy the shape that matches your bowl.







